RISING BARRIER SOLUTIONS
High resistance automatic rising barrier with axial arm up to 6 m
The barrierBAR86is a barrier ofhigh strength safetyequipped with a smooth ofmaximum length of 6 m.
It guarantees continuous intensive service andanti-intrusion resistance. It secures sensitive collective sites and paid car parks requiring enhanced protection while allowing business continuity.
Composition of the BAR86 barrier
-
Shaft and door made of a 3mm thick DKP sheet treated by cataphoresis
-
Cover in 2mm aluminum sheet treated by phosphating
-
Axial reinforced aluminum boom up to 6 m
-
Opening / closing between 2.1 and 7.5 seconds
-
Three-phase motor and 230 V mono power supply
-
Inductive sensors
-
ONE-C control board
BAR86 automatic rising barrier with GA grid
BAR86 rising barrier with GA grid up to 7.5 m
• Secures access with a visual dissuasive aspect
• High impact resistance
• Low hinged grille constituting a physical obstacle for:
- Channeling pedestrians to access control: turnstiles, etc.
- Avoid the intrusion of animals on a protected site
Key Features BAR86 GA Grid
• Low articulated aluminum grid from 3 to 7.5 m
• 84 x 57 mm reinforced aluminum or fiberglass runners Up to Ø 140 mm
• Red and white reflective strips
• Intensive operation
• Guided articulation with removal against the rail
• Ø10, Ø14 and Ø20 mm bars
• Maximum length 7.5 m
• Paint / Finish Polyester powder baked at 250° -
• White and red lacquered
BAR86 automatic rising barrier with GTH grid
BAR86 rising barrier with high and low articulated GTH gate, any height up to 7 m
•Secures access with a visual dissuasive aspect
• Constitutes a physical obstacle for:
- Channel pedestrians to an access control:
turnstiles, …
- Avoid the intrusion of animals on a protected site
- HGV visibility
• Robust, reliable and aesthetic. Provides functions in extreme conditions of use (wind, snow, etc.)
Key Features BAR86 Grille GTH
• High and low hinged aluminum grille
• Aluminum boom from 3 to 7 m
• Intensive operation
• Guided articulation with erasure against the smooth of the 2
sides
• Bars 25 x 3 mm
• Paint / Finish Polyester powder baked at 250° -
• White and red lacquered
• Side rail with red reflective band
84 x 57 mm - LBA 6 and 7 (up to 4m)
135 x 93 mm - LBA 86 (up to 6.5m)
180 x 118 mm - LBA 12 (up to 7m)
• With extended upper grille on the shaft of the barrier
• 40 x 40 x 4 mm aluminum reinforcement tee. V from
reception and anti-sway on rest
• 25 x 3 mm aluminum plate
• Always installed with a rest
BAR86 automatic rising barrier with HP grid
BAR86 rising barrier with high protection HP gridup to 6m
• Secures access with a visual dissuasive aspect
• Ideal substitute for a gate
• High impact resistance
• High and low grid constituting a physical obstacle for:
- Channeling pedestrians to access control: turnstiles, etc.
- Avoid the intrusion of animals on a protected site
- HGV visibility
Main features BAR86 HP Grille
• High protection aluminum grille
• Rectangular aluminum boom 175 x 75 mm, from 2 to 6 m
• Intensive operation
• Equipped with defensive serration
• Ø20 mm rungs
• Paint / Finish Polyester powder baked at 250° -
• White and red lacquered
• Upper rigid grille in standard RAL aluminum
9010; frame 30 x 20 mm and bars Ø 20 mm
• Lower hinged grille in standard RAL 9010 aluminium;
bars Ø 20 mm red (RAL 3020) and white (RAL 9010)
• Rectangular aluminum side profile
175 x 75 mm thickness 2 mm
• With reflective strips
Automatic rising safety barrier BLOKBAR50
BLOKBAR50 automatic safety barrier
Resistance certified by real crash test, classification obtained: 3.5 T at 48 km/h
• Automatic barrier arm height 90cm and length up to 6 m
• Reinforced oval aluminum arm with axial fixing of 135x93mm
• 2 supports with reinforced steel strut
• Low sealing depth
• One-C control card with screen, for easy commissioning and parameter setting
• Continuous operation
• Three-phase geared motor, 230v mono power supply
• Compression compensation spring
• Anti-condensation heater
• Rail support by reinforced axial stirrup
Automatic rising safety barrier BLOKBAR80
ACCESS CONTROLS FOR ALL SITUATIONS
You just have to contact us, Ip-Mirador takes care of the rest...
+33 (0)4 67 24 40 84
Contact our specialized department now, we will advise you on the solution best suited to your needs.
BLOKBAR80 automatic safety barrier
The automatic security barrierBLOKBAR80is designed to ensure thesecurity of sites with a very high level of securityexpected, such asnuclear sitesor classified sitesSEVESO.
Thanks to its shallow sealing, it allows installation on sites where the basements are cluttered with networks.
Resistance certified by real crash test, classification obtained: 7.5T at 80 km/h
• Automatic barrier arm height 90cm and length up to 6 m
• Reinforced oval aluminum arm with axial fixing of 135x93mm
• 2 supports with reinforced steel strut
• Low sealing depth
• One-C control card with screen, for easy commissioning and parameter setting
• Continuous operation
• Three-phase geared motor, 230v mono power supply
• Compression compensation spring
• Anti-condensation heater
• Rail support by reinforced axial stirrup